Home » Electronic Measuring Instruments » Signal, Spectrum & RF Analyzers » Spectrum Analyzer » Anritsu MS2080A Field Master Handheld RF Spectrum Analyzer

Anritsu MS2080A Field Master Handheld RF Spectrum Analyzer

MS2080A Field Master Portable Spectrum Analysis

The Anritsu MS2080A Field Master is a handheld RF spectrum analyzer for wireless-system installation, spectrum monitoring, interference troubleshooting, and field engineering.

Choose the MS2080A-0704 configuration for 9 kHz to 4 GHz or MS2080A-0706 for 9 kHz to 6 GHz. A compact field-oriented design helps technicians move between outdoor sites, equipment rooms, and laboratory benches.

Fast swept analysis, a low displayed average noise level with the preamplifier, and a broad selection of optional measurement functions support a range of spectrum-related tasks. Optional real-time analysis is intended for identifying intermittent and bursty RF activity that conventional sweep measurements may miss.

4 / 6 GHzSelectable upper-frequency configurations
45 GHz/sSpecified spectrum sweep speed
< −165 dBmDisplayed average noise level with preamplifier
40 MHzOptional RTSA analysis bandwidth

The tracking-generator option supports RF insertion-loss investigations, and a separately sold S331P Site Master can extend the workflow to cable and antenna line-sweep measurements. These capabilities are not all included in the base unit.

For high-frequency spectrum analysis beyond 6 GHz, compare the Anritsu MS2090A Field Master Pro already listed by Denkei Americas.

Two Frequency Configurations

Select 9 kHz to 4 GHz (MS2080A-0704) or 9 kHz to 6 GHz (MS2080A-0706) based on the RF bands to be investigated.

High-Speed Swept Measurements

A specified sweep speed of 45 GHz/s helps survey wide frequency spans during site acceptance checks and spectrum troubleshooting.

Optional Real-Time Analysis

Real-time spectrum analysis (Option 0199) with applicable bandwidth configuration supports investigation of transient and bursty signals.

Interference Location Tools

Optional Interference Finder, GNSS and coverage-mapping capabilities assist with locating and documenting problematic RF signals.

Tracking Generator and Cable Test

An optional tracking generator supports insertion-loss measurements; cable/antenna and TDR workflows require a compatible, separately sold S331P unit and relevant options.

LTE / 5G NR Field Measurements

Optional LTE and 5G NR downlink measurement packages support base-station installation, maintenance and performance assessment.

RF Interference Hunting

Identify unwanted signals in operating frequency bands and use configured location tools to help narrow down interference sources.

5G NR Base-Station Testing

Measure selected 5G NR downlink performance indicators when the appropriate 5G option is installed.

LTE Network Maintenance

Perform LTE FDD/TDD checks at cell sites with the matching analyzer option.

Broadcast Transmitter Service

Evaluate spectral occupancy, transmitter emissions and AM/FM characteristics using applicable analyzer functions.

Cable & Antenna Site Checks

Combine an MS2080A with the separately purchased S331P for line-sweep and antenna system maintenance.

RF Filter and Component Checks

Use the optional tracking generator to examine insertion-loss behavior of suitable filters, cables and RF paths.

MS2080A Technical Specifications

Analyzer modelsMS2080A-0704: 9 kHz to 4 GHz; MS2080A-0706: 9 kHz to 6 GHz
Sweep speed45 GHz/s
Displayed average noise level (DANL)< −165 dBm with preamplifier
Phase noise−95 dBc/Hz at 1 GHz carrier frequency and 100 kHz offset
Maximum specified input signal+30 dBm (observe the full input ratings and conditions in the manufacturer datasheet)
Amplitude accuracy±1 dB (±0.5 dB typical), under specified conditions
Swept resolution bandwidth1 Hz to 5 MHz
Zero-span resolution bandwidth10 Hz to 20 MHz
Optional real-time spectrum analysisUp to 40 MHz RTSA bandwidth with required options
Tracking generator output (optional)−45 to +9 dBm; tracking, offset-tracking and CW modes
Optional cable/antenna functionRequires separate S331P Site Master hardware; additional options may be necessary
Portable form factorWeight below 4 kg (less than 9 lb), per manufacturer
Available cellular measurement optionsLTE FDD/TDD; 5G NR downlink; WCDMA FDD
Optional measurement / workflow featuresGNSS receiver, interference finder, channel scanner, coverage mapping, IQ capture / streaming

Measurement, RTSA, tracking generator, GNSS and cellular capabilities depend on installed options. The 40 MHz RTSA bandwidth is not a standard base-unit guarantee.