AIKOH 1605K Series Precision force tester

500 N Precision Force Testing for Connectors and Small Components

The AIKOH 1605K and 1605KL precision force testers provide up to 500 N capacity with adjustable 0.5–600 mm/min motion for controlled force and displacement evaluation of electronic and mechanical parts.

The desktop 1605K Series uses a servo drive, rigid frame and MODEL-1018 force-measuring amplifier. Both models support connector mating and unmating tests, small-component strength measurements, controlled bending and product evaluation.

500 N Maximum test force (50 kgf)
0.5–600 mm/min Adjustable servo-driven test speed
0.001 N Minimum force indication with a 5 N load cell
0.001 mm 1605KL linear-gauge display resolution

The 1605K measures displacement with a rotary encoder, while the 1605KL offers selectable rotary-encoder and linear-gauge detection. The linear gauge enables 0.001 mm display resolution over a 25 mm measurement range, useful for smaller displacement changes.

Test fixtures, load-cell selection and optional ON/OFF detection should be matched to the sample. This page describes current 1605K/1605KL specifications rather than discontinued 1605VC/1605VCL specifications.

500 N Precision Test Platform

A rigid benchtop system supports connector insertion/extraction force testing and component strength evaluation.

Controlled Servo Motion

Test speed from 0.5 to 600 mm/min with 15-step or stepless selection allows flexible motion profiles.

Fine Force Indication

Minimum force indication reaches 0.001 N with a 5 N load cell; accuracy depends on the selected cell.

Two Displacement Options

1605K uses a rotary encoder; 1605KL additionally provides linear-gauge displacement detection.

0.001 mm Linear-Gauge Display

1605KL supports fine displacement indication across its 25 mm linear-gauge measurement range.

Application-Specific Accessories

Additional load cells, custom fixtures and an optional MODEL-0219 ON/OFF detector support varied test configurations.

Connector Mating and Unmating

Measure insertion and withdrawal forces during connector design validation or quality checks.

Small-Component Compression

Apply controlled compressive force to electronic or mechanical parts and measure their response.

Small-Component Tensile Testing

Evaluate pull strength of miniature assemblies with appropriately sized grips.

Three-Point Bending Tests

Test deflection and load response with an application-matched bending fixture.

Switch Actuation Evaluation

Measure switch force response with appropriate test fixtures and optional contact detection.

Product R&D and Quality Control

Compare force-displacement behavior among design iterations, incoming lots or production samples.

Specification 1605K 1605KL
Maximum Force 500 N (50 kgf) 500 N (50 kgf)
Force Accuracy Depends on load cell Depends on load cell
Force Amplifier MODEL-1018 MODEL-1018
Controller Built in Built in
Test Speed 0.5–600 mm/min 0.5–600 mm/min
Speed Adjustment 15 steps or stepless 15 steps or stepless
Mechanical Stroke 255 mm 255 mm; 25 mm with linear gauge
Displacement Detector Rotary encoder Rotary encoder / linear gauge
Displacement Display Resolution 0.01 mm (encoder) 0.01 mm (encoder) / 0.001 mm (linear gauge)
Displacement Display Accuracy 0.1 mm (encoder) Consult manufacturer for linear-gauge accuracy
Test Center to Column 100 mm 100 mm
Table Size W475 × D150 mm; M10 × 1.5 W475 × D150 mm; M10 × 1.5
Drive Motor Servo motor Servo motor
Dimensions (W × H × D) 480 × 578 × 375 mm 480 × 882 × 375 mm
Stand Mass Approx. 44 kg Approx. 45 kg
Power Supply Single-phase AC 100–240 V, 5 A Single-phase AC 100–240 V, 5 A

0.001 mm is the 1605KL linear-gauge display resolution, not an accuracy claim. Manufacturer pages and catalogs differ slightly in overall height figures; the table follows the AIKOH English model pages. Load cells, jigs and optional interfaces affect the final configuration.