HIOKI RM3546 Resistance Meter

1 nΩ Weld Resistance Inspection for EV Battery Manufacturing

The HIOKI RM3546 is an ultra-high-resolution resistance meter for quality inspection of welded battery busbars and interconnections, featuring 1 nΩ resolution and advanced compensation functions.

Built for battery module and pack production lines, the RM3546 measures tiny differences in DC resistance to support consistent weld assessment. Advanced Offset Voltage Compensation (A-OVC) and Advanced Temperature Correction (A-TC) help stabilize results, including immediately after welding when temperatures change rapidly.

1 nΩ Best available resistance resolution
A-TC Advanced post-weld temperature correction
A-OVC Compensation for voltage offsets
60 V DC Active circuit protection limit

Active Circuit Protection (ACP) reduces instrument damage risk from accidental voltage application within its stated limits. The design also offers up to 9 Ω of path resistance tolerance only under specified PR1000 µΩ / 500 mA conditions.

Optional Z3003 multiplexer modules enable up to 20 four-terminal test points, while an external SW1002 can provide up to 132 four-terminal channels. The RM3546 is not intended to measure energized connections or battery internal resistance; isolate the target and follow all measurement safety requirements.

Ultra-Low 1 nΩ Resolution

Distinguishes small resistance variations in battery busbar and weld joints.

Advanced Offset Voltage Compensation

A-OVC suppresses thermoelectric and other offset effects during precision low-resistance tests.

Advanced Temperature Correction

A-TC accounts for post-weld temperature changes and supports earlier resistance inspection.

Active Circuit Protection

ACP helps protect the measurement circuit against accidental voltage application up to ±60 V DC within stated conditions.

Robust Measurement Paths

PR mode supports as much as 9 Ω path resistance tolerance in the specified 500 mA test condition.

Expandable Channel Capacity

Supports two optional Z3003 units for 20 four-terminal points or SW1002 for up to 132 points.

Battery Busbar Weld Inspection

Check welding consistency of battery module busbar connections.

Battery Pack Interconnect Quality

Quantify low-resistance joints during EV and ESS pack assembly.

Post-Weld Production Testing

Apply advanced temperature correction when checking recently welded components.

Battery Module End-of-Line QC

Record resistance judgments for manufacturing traceability.

Automated Multi-Point Inspection

Connect multiplexers and production control systems for serial measurement of weld sites.

Welding Process Development

Compare resistance changes across welding settings and material combinations.

Specification RM3546
Measurement function Precision four-terminal DC resistance
Nominal resistance range 1000 µΩ to 1000 MΩ (13 ranges)
Best resolution 1 nΩ (1000 µΩ range)
Representative accuracy, 1000 µΩ range ±0.045% rdg. ±0.010% f.s.
Representative accuracy, 1000 mΩ range ±0.012% rdg. ±0.001% f.s.
Testing current Up to 1 A DC
FAST measurement time 2.3 ms (representative, range dependent)
Advanced compensation A-OVC and A-TC
Active circuit protection Up to ±60 V DC; or 30 V AC rms / 42.4 V AC peak
Maximum path resistance tolerance Up to 9 Ω under PR1000 µΩ, 500 mA conditions
Built-in multiplexer (option) 2 × Z3003: up to 20 points, four-wire
External multiplexer (option) SW1002: up to 132 points, four-wire
Interfaces LAN, RS-232C, USB, EXT. I/O
Supply 100–240 V AC, 50/60 Hz; 40 VA max.
Dimensions / mass 215 × 80 × 306.5 mm; approximately 3.4 kg

Specifications depend on range and settings. ACP is intended for accidental voltage exposure, not measurement of energized circuits or a battery’s internal resistance. Switch off and isolate the target before measuring. Z3003 and SW1002 are optional.