Home » Electronic Measuring Instruments » Signal & Waveform Generators » Function Generator » NF Corporation WF1973 / WF1974 Multifunction Generator

NF Corporation WF1973 / WF1974 Multifunction Generator

Legacy 30 MHz Precision Function Synthesis

The discontinued NF Corporation WF1973 and WF1974 multifunction generators provide one- and two-channel 30 MHz signal generation with precise frequency control, parameter-variable waveforms and programmable sequences for laboratory and electronics testing.

Discontinued; NF identifies WF1981 / WF1982 as the successor.

The WF1973 provides one output channel; the WF1974 adds two-channel independent and coupled-operation modes for phase-related, differential and constant-ratio signals. Its broad waveforms support analog electronics, ECU sensors and industrial control experiments.

NF specifies a 0.01 µHz frequency setting resolution, ±(3 ppm of setting + 2 pHz) frequency accuracy and a sequence function for controlled changes in waveform, amplitude, frequency and other settings. Actual supported modes and numerical performance depend on signal configuration.

NF marks both WF1973 and WF1974 as discontinued and recommends WF1981 / WF1982. The successor has updated interfaces, waveform capacity and sub-output capabilities and should be evaluated against the installed test procedure.

30 MHzMaximum sine-wave frequency
1 / 2 CHWF1973 / WF1974 main channels
0.01 µHzFrequency setting resolution
255 stepsSequence length limit

30 MHz Signal Generation

Set precision sine-wave signals over a broad frequency range for benchtop tests.

Two Model Choices

Use WF1973 for one main output or WF1974 for two with linked waveform operation.

Precise Frequency Control

Frequency accuracy is specified as ±(3 ppm of setting + 2 pHz) under maker conditions.

Parameter-Variable Waveforms

Configure characteristic waveform shapes by editing defined waveform parameters.

Sequence Programming

Construct up to 255 output steps per sequence to automate changing test conditions.

Floating Output Architecture

The main channel output terminals are isolated from the instrument housing, with rated limits.

Analog Circuit Characterization

Apply precise waveforms to evaluate analog and mixed-signal electronic assemblies.

Automotive ECU Testing

Reproduce sensor and gear-rotation signal patterns used in bench-level controller verification.

Ultrasonic Drive Research

Provide repeatable waveform stimuli for motor and ultrasonic-device experiments.

Balanced Input Evaluation

Test differential and paired-signal circuits using WF1974 linked channel functions.

Audio Signal Chain Testing

Generate tone bursts and sweeps for amplifiers, speakers and signal-processing devices.

Legacy Bench Replacement Planning

Compare established WF1973/WF1974 test sequences with WF1981/WF1982 capabilities.

SpecificationWF1973WF1974
Product statusDiscontinued; successor WF1981Discontinued; successor WF1982
Main output channels12
Maximum sine-wave frequency30 MHz30 MHz
Minimum specified sine frequency0.01 µHz0.01 µHz
Frequency setting resolution0.01 µHz0.01 µHz
Frequency accuracy±(3 ppm of setting + 2 pHz)±(3 ppm of setting + 2 pHz)
Amplitude setting accuracy±(1% of setting + 2 mVp-p) / open±(1% of setting + 2 mVp-p) / open
Phase setting resolution0.001°0.001°
Available waveformsSine, square, pulse, ramp, noise, DC, arbitrary, parameter-variableSine, square, pulse, ramp, noise, DC, arbitrary, parameter-variable
Sequence stepsUp to 255 per sequenceUp to 255 per sequence
Main output couplingSingle-channelIndependent, two-phase, differential, frequency-ratio and difference
InterfacesUSB, GPIBUSB, GPIB
Output isolationSignal outputs insulated from housing (within ratings)Signal outputs insulated from housing (within ratings)

These figures describe discontinued WF1973/WF1974, not the later WF1981/WF1982. Numerical waveform/frequency limits vary by mode; confirm the original NF specification before reproducing an existing test procedure.