Home » Electronic Measuring Instruments » Bidirectional & Bipolar Power Sources » Bipolar Power Supply » NF Corporation BP series Bipolar DC Power Supply

NF Corporation BP series Bipolar DC Power Supply

NF Corporation BP Series Bipolar DC Power Supply

Four-quadrant voltage and current sourcing for dynamic component and power-electronics tests.

NF Corporation’s BP Series combines bipolar voltage output with source and sink operation, enabling current in either direction and supporting energy-returning or inductive loads that challenge conventional unidirectional DC power supplies. This makes the series particularly relevant for coils, solenoids, motor-related devices and electronic-component evaluation.

The lineup covers ten DC current ratings from ±10 A to ±100 A while maintaining a nominal ±60 V output range. An offset output window can be shifted toward +115 V or -115 V by changing voltage limits; the full symmetric ±60 V swing is not available at the shifted extreme.

Select between constant-voltage (CV) and constant-current (CC) control and program repeatable voltage or current profiles using the built-in sequence generator. High-frequency and fast-transition figures are conditional on model, load and test settings, so they should not be treated as full-current bandwidth ratings.

±60 V

Nominal bipolar voltage window (120 Vp-p).

±10–100 A

Ten model-specific DC current ratings.

4 Quadrants

Both polarities with source and sink capability.

255 Steps

Built-in programmable sequence generator.

Four-Quadrant Output

Source and absorb current at positive and negative voltage polarities for complex test loads.

Model-Specific Current Capacity

Choose from BP4610 through BP46100 to match 10 A through 100 A bipolar DC current requirements.

CV and CC Control

Switch between regulated voltage and current operation for resistive, inductive and capacitive devices.

Programmable Sequences

Build output patterns using the internal sequence function with up to 255 steps.

Fast Low-Amplitude Response

BP4610/4620 support up to 200 kHz small-amplitude CV response under specified conditions; full-output performance differs.

Integration Interfaces

Use USB, external control I/O and included control software for automated evaluation.

Automotive Voltage Disturbance Testing

Create voltage fluctuation profiles for 12 V, 24 V and 48 V-class component investigations.

Solenoid and Coil Excitation

Provide controlled bipolar current to inductive actuators and magnetic devices.

Capacitor Ripple Current Evaluation

Drive configured ripple currents into capacitive circuits or inverter components.

Motor Component Development

Test inductive motor subassemblies and back-EMF-related electrical behavior.

Magnetic Field Generation

Supply regulated current to test coils for repeatable field generation.

Automated Component Stress Tests

Program repeatable polarity reversals and current/voltage transitions in a bench or ATE sequence.

Technical Specifications

ParameterSpecification
Operating principleBipolar DC source/sink with four-quadrant operation
Nominal output voltage±60 V (120 V peak-to-peak)
Shifted voltage windowUp to approximately +115 V or -115 V at a shifted 120 Vp-p window; current capability changes
DC output current lineup±10, ±20, ±30, ±40, ±50, ±60, ±70, ±80, ±90, ±100 A by model
Control modesConstant voltage (CV), constant current (CC)
Sequence capacityUp to 255 steps per sequence
Sequence step time0.1 ms to 999.9999 s, 0.1 ms resolution
Waveform outputDC, sine, square and arbitrary waveform functions
Small-amplitude response — BP4610/BP4620CV: DC to 200 kHz; CC: DC to 70 kHz under specified test/adjustment conditions
High-frequency full-output limitModel/load/frequency dependent; do not infer ±60 V at 200 kHz
Voltage/current limitersAdjustable limits to suit device under test
ControlUSB, external control I/O, bundled software
Output synchronizationProgrammable sequence and external amplifier operation; implementation per model
Power inputLarge models require order-specified three-phase input configuration
CertificationBP4610 and BP4620 listed by NF as CE-certified; do not generalize to all models

Model / Configuration Comparison

ModelRated DC bipolar currentModelRated DC bipolar current
BP4610±10 ABP4660±60 A
BP4620±20 ABP4670±70 A
BP4630±30 ABP4680±80 A
BP4640±40 ABP4690±90 A
BP4650±50 ABP46100±100 A

Manufacturer comparison: the BP Series marketing page gives DC to 150 kHz CV bandwidth as a series feature, while BP4610/4620 can reach DC to 200 kHz only under specified small-amplitude conditions. These are not equivalent to full-power switching bandwidth.